Kern-sohn CH 50K100 Instrukcja Użytkownika

KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: [email protected] Phone: +49-[0]7433- 9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern

3.2 Overview visual displays and keyboard Displays: kg The current measuring unit is kilogram lb The current measuring unit is pound N The

3.3 Label  Do not stand or go under suspended loads.  Do not use on building site.  Keep an eye on suspended loads. (example)  Do not exce

4. Commissioning + Always observe chapter 2 „General Safety Instructions“! 4.1 Unpacking SAFETY INSTRUCTIONS for protection against break Once

4.3 Checking the original dimensions  Enter the original dimensions shown on the production data sheet in the grey boxes of checklist chap. 8.3. 

5. Operation Keep balance only by hand, see fig. (do not use a crane or alike). 5.1 Safety instructions DANGER Risk of injury due to

 Take great care when operating the crane and follow the general rules for crane operation.  Check all parts (hook, carbines, rings, r

5.2 Loading the suspended balance For good weighing results observe the following, illustrations see next page:  Do not suspend the balance on load

Keep balance only by hand! Do not push or pull Do not pull the hook horizontally CH-BA-e-1432 17

5.3 Turn on/off Start-up  Press the ON/OFF/TARE-key. The display lights up and the balance carries out a selftest. The selftest is completed when

5.6 Switch-over weighing unit The next measuring unit will be displayed kg lbN after each press of the UNIT button. The  indicator shows the ac

GB KERN CH Version 3.2 08/2014 Operating instructions / Logbook Electronic Suspending Balance Contents 1. Technical data ___________________

5.7.1 Data-Hold function  Switch on the balance, keep the HOLD-button pressed until the current setting „Hx“ (H1 – H6) appears.  Press ON/OFF/TAR

5.7.3 Peak value function This function displays the highest load value (peak value) of a weighing. Measuring frequency: 200ms Attention: Never ex

7. Adjustment As the acceleration value due to gravity is not the same at every location on earth, each balance must be coordinated - in compliance w

8. Cleaning, Maintenance and Disposal Danger Risk of injury and risk of material damage! The suspended balance is part of the lifting gear! For

8.2 Regular maintenance and care  The regular 3-month maintenance may only be carried out by an expert with competent knowledge of working with su

Regular maintenance: Prior to each usage  Check for fault-free operation of the attachment devices Initial start-up, every 3 months or definitely a

8.3 Checklist „Regular maintenance“ Original dimensions suspended balance*, serial no.: ………………………………… Capacity ……………………………… Total scale Hooks d (

Total scale Hooks Optical test d Safety fastening e f g h i α Wear (see cross-hatched areas) No deformation, wear or cracks Date Tester han

1 Chain link CH-BA-e-1432 28

9. Enclosure 9.1 Checklist „Enhanced maintenance“ (General revision) The enhanced maintenance has to be carried out by a service partner authorized

1. Technical data KERN CH 15K20 CH 50K50 CH 50K100 Readability (d) 20 g 50 g 100 g Weighing range (max) 15 kg 50 kg 50 kg Taring range (sub

10. Declaration of conformity KERN & Sohn GmbH D-72322 Balingen-Frommern Postbox 4052 E-Mail: [email protected] Phone: 0049-[0]7433- 9933-0 Fax:

1.1 Dimensions 4 CH-BA-e-1432

2. General Safety Instructions 2.1 Duties of the owner-operator Follow national accident prevention regulations and all operator health and safety a

2.4 Pay attention to the instructions in the Operation Manual  Carefully read this operation manual before setup and commissioning, even if you are

2.8 Safe working  Do not stand under swinging loads, see chap. 5.1. 2.9 Monitoring of Test Resources In the framework of quality assurance the me

3. The suspended balance at a glance 3.1 Overview 1 Display 2 Keyboard 3 Hooks 4 Tape measure 8 CH-BA-e-1432

1 Battery compartment 2 Tape measure CH-BA-e-1432 9